Cannon Gas Miser Manually
Search: Fixed for free! Popular These categories may also be of interest. Mend, fix, or repair just about anything. Help someone Are you good at fixing things? To help Fault info.
Power Sliding Moonroof w/Tilt; Manual Folding Outside Mirrors; Power Windows. Sedan, with less than 14k miles, pretty much brand new*** Gas miser!!!
Howtomendit.com costs nothing to use and you can ask a question without an account or logging in. To ask a question. Answers Who answers the questions? Other users of howtomendit.com provide the answers. The more detail and information you provide in your question the easier it is for others to help you. Search for a fix Mend it.
> How can I fix my Cannon gas fire? I have a Cannon Coalridge Gas Fire which is not lighting. The pilot light comes on, but the fire will not light after holding the pilot on for the required time. Is this likey to be a new Thermocouple needed? Tim Lambert January 2008 why the brick on my cannon gas fire not glowing gareth February 2015 where can i buy gasket material for the front glass and does it have to seal to prevent CO2 leakage? It is a Cano Coalridge Thanks in advance for any advice offered Alex October 2013 Cleaned the spade connectors as recommended by Julie. Lit first time after that and still burning after an hour.
Malc March 2013 Mine has just exploded while trying to ignite - could have seriously injured somebody - peppered opposite wall and sofa with shards of glass. If you have one, just get rid of it. Dave Batstone December 2012 iv just had this problem got the part off e bay fitting was simple and fire works fine and no im not a gas safe registed but iv do know what im doing and have proper tools gas safe a nice way to earn money December 2012 It is the safety device.
When the pilot is lit it heats the thermocouple that reacts through temprature/expansion relationship with a sprung seated valve that stops gas being supplied to the main burners. When the thermocouple is hot enough it allows this seated valve to lift so that when you release from the pilot position gas is ready to be delivered to your main burners. When you now turn your flame position control a sprung loade ported valve turns allow differing rates of gas to flow. Your Sprung loaded valve has probably broke at the control spring.
It is under the aluminium M8 nut at the back. I dont know if you can buy this spare, i imagine its very cheap to produce so you may have to buy a new control valve. I'm not a gas engineer just an engineer who has a greater interest in how thing work rather than taking money out of your pocket. Looking at them it should take a registered competent gas fitter no longer than 15 minutes to change plus his post fit checks.
It's a shame you cant do it yourself and just get someone in to safe regiter it but hey thats the way it goes. Colin September 2012 with people like Robert that dose not know the difference between a thermocouple & a injector you should be careful about some of the advice you are given, and get a registered gas safe engineer.it might cost you £50-70 but it will be safe & correct. PS It is also illegal to work on gas appliances yourself, so if things do go wrong you would find your house insurance would not cover you Les. Gas Safe Reg: Engineer March 2010 have a cannon coalridge fire 16 years old. Had saftey check and failed due to saftey device not working.its only as big as a pen top but you cant get them you have to replace the whole unit at a cost of £90 plus fitting. Mine was not shutting off.
Yours is the reverse.if you look where th thremocouple screws in you will find a aluminium nut the little unit is behind there. The best way and safest is to call a gas engineer.
Steve September 2009 Ok, so now you have cleaned the jet/replaced the thermocouple: technicaly you have done work on the gas fire. How are you going to check it is safe to use!! You don't know do you!!
That's why you have to pay a gas safe regisetered engineer to do the work. He will comply with the Gas regulations and provide you with the peace of mind that your nearest and dearest won't be harmed. He needs to earn a living, so it might cost you £50-60 Shaver! June 2009 get a quilified gas engineer and stop messing around with appliances that can be lethal in the wrong hands. Just read answer from robert, what he describes is the injector not the thermocouple, so much for diy bodgers gerry owen March 2009 all of you should make sure that the fire is safe to use after messing around with it.
It does not take much to upset the fsd and if not checked propely the fire could be un-safe and cause CO gary January 2009 Tim, I have the same fire and have just had it repaired with the same problem. Remove the two screws holding the cast iron top cover and lift it off. Next remove the front base and then the gold covers. They just lift off. Then remove all the screws and plates holding the glass cover onand carefully remove the glass.